MIB Discovery
1856 modules enregistr├ęs
Chemin
MIX : 1 (iso). 3 (org). 6 (dod). 1 (internet). 2 (mgmt). 1 (mib-2). 127 (docsIetfQosMIB). 1 (docsIetfQosMIBObjects). 1 (docsIetfQosPktClassTable). 1 (docsIetfQosPktClassEntry). 20 (docsIetfQosPktClassEnetProtocolType)
OID : 1.3.6.1.2.1.127.1.1.1.20
TXT : iso. org. dod. internet. mgmt. mib-2. docsIetfQosMIB. docsIetfQosMIBObjects. docsIetfQosPktClassTable. docsIetfQosPktClassEntry. docsIetfQosPktClassEnetProtocolType
Enfants
Pas d'enfants disponibles pour cet OID
D├ętails
OID1.3.6.1.2.1.127.1.1.1.20
Module DOCS-IETF-QOS-MIB (CISCO)
NomdocsIetfQosPktClassEnetProtocolType
Accesreadonly
Statuscurrent
DescriptionThis object indicates the format of the layer 3 protocol ID in the Ethernet packet. A value of none(0) means that the rule does not use the layer 3 protocol type as a matching criteria. A value of ethertype(1) means that the rule applies only to frames that contain an EtherType value. Ethertype values are contained in packets using the Dec-Intel-Xerox (DIX) encapsulation or the RFC1042 Sub-Network Access Protocol (SNAP) encapsulation formats. A value of dsap(2) means that the rule applies only to frames using the IEEE802.3 encapsulation format with a Destination Service Access Point (DSAP) other than 0xAA (which is reserved for SNAP). A value of mac(3) means that the rule applies only to MAC management messages for MAC management messages. A value of all(4) means that the rule matches all Ethernet packets. If the Ethernet frame contains an 802.1P/Q Tag header (i.e., EtherType 0x8100), this object applies to the embedded EtherType field within the 802.1P/Q header. If the referenced parameter is not present in a classifier, this object reports the value of 0.
SyntaxeEnumeration (0-none, 1-ethertype, 2-dsap, 3-mac, 4-all)
Module DOCS-IETF-QOS-MIB (ietf)
NomdocsIetfQosPktClassEnetProtocolType
Accesreadonly
Statuscurrent
DescriptionThis object indicates the format of the layer 3 protocol ID in the Ethernet packet. A value of none(0) means that the rule does not use the layer 3 protocol type as a matching criteria. A value of ethertype(1) means that the rule applies only to frames that contain an EtherType value. Ethertype values are contained in packets using the Dec-Intel-Xerox (DIX) encapsulation or the RFC1042 Sub-Network Access Protocol (SNAP) encapsulation formats. A value of dsap(2) means that the rule applies only to frames using the IEEE802.3 encapsulation format with a Destination Service Access Point (DSAP) other than 0xAA (which is reserved for SNAP). A value of mac(3) means that the rule applies only to MAC management messages for MAC management messages. A value of all(4) means that the rule matches all Ethernet packets. If the Ethernet frame contains an 802.1P/Q Tag header (i.e., EtherType 0x8100), this object applies to the embedded EtherType field within the 802.1P/Q header. If the referenced parameter is not present in a classifier, this object reports the value of 0.
SyntaxeEnumeration (0-none, 1-ethertype, 2-dsap, 3-mac, 4-all)