| OID | 1.3.6.1.2.1.10.127.1.1.2.1.18 |
| Module | DOCS-IF-MIB (CISCO) |
| Nom | docsIfUpChannelStatus |
| Acces | readwrite |
| Status | current |
| Description | This object is only used for the creation of a temporary
upstream row with the purpose of updating the parameters
of a physical upstream channel entry.
The following restrictions apply to this object:
1. This object is not writable for physical interfaces.
2. Temporary interface entries are only created by a SET
of this object to createandWait(5).
3. ifAdminStatus from the Interface MIB RFC 2863 is used
to take a physical upstream channel offline, to be
consistent with DOCSIS 1.x operation, as indicated in
RFC 2670.
In addition,
o ifAdminStatus 'down' is reflected in this object
as 'notInService'.
o ifOperStatus 'down' while ifAdminStatus 'up' is
reflected in this object as 'notInservice'.
4. Temporary created rows MUST be set to 'active' with
the purpose of validating upstream parameter
consistency prior to transferring the parameters to the
physical interface.
Below is a mandatory procedure for adjusting the values
of a physical interface:
1. Create a temporary interface entry through an SNMP SET
using 'createAndWait'. At this point, the RowStatus
reports 'notReady'.
The Manager entity uses an ifIndex value outside the
operational range of the physical interfaces for the
creation of a temporary interface.
2. Set the docsIfUpChannelCloneFrom object to the ifIndex
value of the physical row to update. Now
docsIfUpChannelStatus reports 'notInService'.
3. Change the upstream parameters to the desired values
in the temporary row.
4. Validate that all parameters are consistent by setting
docsIfUpChannelStatus to 'active'. A failure to set the
RowStatus to 'active' returns the error 'commitFailed',
which means the parameters are not compatible with the
target physical interface.
5. With docsIfUpChannelStatus 'active', transfer the
parameters to the target physical interface by setting
the object docsIfUpChannelUpdate to 'true'.
6. Delete the temporary row by setting
docsIfUpChannelStatus to 'destroy'. |
| Syntaxe | RowStatus (SNMPv2-TC) |
| Module | DOCS-IF-MIB (ietf) |
| Nom | docsIfUpChannelStatus |
| Acces | readwrite |
| Status | current |
| Description | This object is only used for the creation of a temporary
upstream row with the purpose of updating the parameters
of a physical upstream channel entry.
The following restrictions apply to this object:
1. This object is not writable for physical interfaces.
2. Temporary interface entries are only created by a SET
of this object to createandWait(5).
3. ifAdminStatus from the Interface MIB RFC 2863 is used
to take a physical upstream channel offline, to be
consistent with DOCSIS 1.x operation, as indicated in
RFC 2670.
In addition,
o ifAdminStatus 'down' is reflected in this object
as 'notInService'.
o ifOperStatus 'down' while ifAdminStatus 'up' is
reflected in this object as 'notInservice'.
4. Temporary created rows MUST be set to 'active' with
the purpose of validating upstream parameter
consistency prior to transferring the parameters to the
physical interface.
Below is a mandatory procedure for adjusting the values
of a physical interface:
1. Create a temporary interface entry through an SNMP SET
using 'createAndWait'. At this point, the RowStatus
reports 'notReady'.
The Manager entity uses an ifIndex value outside the
operational range of the physical interfaces for the
creation of a temporary interface.
2. Set the docsIfUpChannelCloneFrom object to the ifIndex
value of the physical row to update. Now
docsIfUpChannelStatus reports 'notInService'.
3. Change the upstream parameters to the desired values
in the temporary row.
4. Validate that all parameters are consistent by setting
docsIfUpChannelStatus to 'active'. A failure to set the
RowStatus to 'active' returns the error 'commitFailed',
which means the parameters are not compatible with the
target physical interface.
5. With docsIfUpChannelStatus 'active', transfer the
parameters to the target physical interface by setting
the object docsIfUpChannelUpdate to 'true'.
6. Delete the temporary row by setting
docsIfUpChannelStatus to 'destroy'. |
| Syntaxe | RowStatus (SNMPv2-TC) |