| OID | 1.3.6.1.2.1.10.7.11 |
| Module | EtherLike-MIB (CISCO) |
| Nom | dot3HCStatsTable |
| Status | current |
| Description | A table containing 64-bit versions of error
counters from the dot3StatsTable. The 32-bit
versions of these counters may roll over quite
quickly on higher speed ethernet interfaces.
The counters that have 64-bit versions in this
table are the counters that apply to full-duplex
interfaces, since 10 Gb/s and faster
ethernet-like interfaces do not support
half-duplex, and very few 1000 Mb/s
ethernet-like interfaces support half-duplex.
Entries in this table are recommended for
interfaces capable of operating at 1000 Mb/s or
faster, and are required for interfaces capable
of operating at 10 Gb/s or faster. Lower speed
ethernet-like interfaces do not need entries in
this table, in which case there may be fewer
entries in this table than in the
dot3StatsTable. However, implementations
containing interfaces with a mix of speeds may
choose to implement entries in this table for
all ethernet-like interfaces. |
| Module | EtherLike-MIB (DELL) |
| Nom | dot3HCStatsTable |
| Status | current |
| Description | A table containing 64-bit versions of error
counters from the dot3StatsTable. The 32-bit
versions of these counters may roll over quite
quickly on higher speed ethernet interfaces.
The counters that have 64-bit versions in this
table are the counters that apply to full-duplex
interfaces, since 10 Gb/s and faster
ethernet-like interfaces do not support
half-duplex, and very few 1000 Mb/s
ethernet-like interfaces support half-duplex.
Entries in this table are recommended for
interfaces capable of operating at 1000 Mb/s or
faster, and are required for interfaces capable
of operating at 10 Gb/s or faster. Lower speed
ethernet-like interfaces do not need entries in
this table, in which case there may be fewer
entries in this table than in the
dot3StatsTable. However, implementations
containing interfaces with a mix of speeds may
choose to implement entries in this table for
all ethernet-like interfaces. |
| Module | EtherLike-MIB (ietf) |
| Nom | dot3HCStatsTable |
| Status | current |
| Description | A table containing 64-bit versions of error
counters from the dot3StatsTable. The 32-bit
versions of these counters may roll over quite
quickly on higher speed ethernet interfaces.
The counters that have 64-bit versions in this
table are the counters that apply to full-duplex
interfaces, since 10 Gb/s and faster
ethernet-like interfaces do not support
half-duplex, and very few 1000 Mb/s
ethernet-like interfaces support half-duplex.
Entries in this table are recommended for
interfaces capable of operating at 1000 Mb/s or
faster, and are required for interfaces capable
of operating at 10 Gb/s or faster. Lower speed
ethernet-like interfaces do not need entries in
this table, in which case there may be fewer
entries in this table than in the
dot3StatsTable. However, implementations
containing interfaces with a mix of speeds may
choose to implement entries in this table for
all ethernet-like interfaces. |
| Module | EtherLike-MIB (Force10-9.14.2.1) |
| Nom | dot3HCStatsTable |
| Status | current |
| Description | A table containing 64-bit versions of error
counters from the dot3StatsTable. The 32-bit
versions of these counters may roll over quite
quickly on higher speed ethernet interfaces.
The counters that have 64-bit versions in this
table are the counters that apply to full-duplex
interfaces, since 10 Gb/s and faster
ethernet-like interfaces do not support
half-duplex, and very few 1000 Mb/s
ethernet-like interfaces support half-duplex.
Entries in this table are recommended for
interfaces capable of operating at 1000 Mb/s or
faster, and are required for interfaces capable
of operating at 10 Gb/s or faster. Lower speed
ethernet-like interfaces do not need entries in
this table, in which case there may be fewer
entries in this table than in the
dot3StatsTable. However, implementations
containing interfaces with a mix of speeds may
choose to implement entries in this table for
all ethernet-like interfaces. |