| OID | 1.3.6.1.2.1.16.11.2.1.7 |
| Module | RMON2-MIB (CISCO) |
| Nom | protocolDirHostConfig |
| Acces | readwrite |
| Status | current |
| Description | This object describes and configures the probe's support for
the network layer and application layer host tables for this
protocol. When the probe creates entries in this table for
all protocols that it understands, it will set the entry to
notSupported(1) if it doesn't have the capability to track the
nlHostTable for this protocol or if the alHostTable is
implemented but doesn't have the capability to track this
protocol. Note that if the alHostTable is implemented, the
probe may only support a protocol if it is supported in both
the nlHostTable and the alHostTable.
If the associated protocolDirType object has the
addressRecognitionCapable bit set, then this is a network
layer protocol for which the probe recognizes addresses, and
thus the probe will populate the nlHostTable and alHostTable
with addresses it discovers for this protocol.
If the value of this object is notSupported(1), the probe
will not track the nlHostTable or alHostTable for this
protocol and shall not allow this object to be changed to any
other value. If the value of this object is supportedOn(3),
the probe supports tracking of the nlHostTable and alHostTable
for this protocol and is configured to track both tables
for this protocol for all control entries and all interfaces.
If the value of this object is supportedOff(2), the probe
supports tracking of the nlHostTable and alHostTable for this
protocol but is configured to not track these tables
for any control entries or interfaces.
Whenever this value changes from supportedOn(3) to
supportedOff(2), the probe shall delete all related entries in
the nlHostTable and alHostTable.
Note that since each alHostEntry references 2 protocol
directory entries, one for the network address and one for the
type of the highest protocol recognized, that an entry will
only be created in that table if this value is supportedOn(3)
for both protocols. |
| Syntaxe | Enumeration (1-notSupported, 2-supportedOff, 3-supportedOn) |
| Module | RMON2-MIB (ietf) |
| Nom | protocolDirHostConfig |
| Acces | readwrite |
| Status | current |
| Description | This object describes and configures the probe's support for
the network-layer and application-layer host tables for this
protocol. When the probe creates entries in this table for
all protocols that it understands, it will set the entry to
notSupported(1) if it doesn't have the capability to track the
nlHostTable for this protocol or if the alHostTable is
implemented but doesn't have the capability to track this
protocol. Note that if the alHostTable is implemented, the
probe may only support a protocol if it is supported in both
the nlHostTable and the alHostTable.
If the associated protocolDirType object has the
addressRecognitionCapable bit set, then this is a network-
layer protocol for which the probe recognizes addresses, and
thus the probe will populate the nlHostTable and alHostTable
with addresses it discovers for this protocol.
If the value of this object is notSupported(1), the probe
will not track the nlHostTable or alHostTable for this
protocol and shall not allow this object to be changed to any
other value. If the value of this object is supportedOn(3),
the probe supports tracking of the nlHostTable and alHostTable
for this protocol and is configured to track both tables
for this protocol for all control entries and all interfaces.
If the value of this object is supportedOff(2), the probe
supports tracking of the nlHostTable and alHostTable for this
protocol but is configured to not track these tables
for any control entries or interfaces.
Whenever this value changes from supportedOn(3) to
supportedOff(2), the probe shall delete all related entries in
the nlHostTable and alHostTable.
Note that since each alHostEntry references 2 protocol
directory entries, one for the network address and one for the
type of the highest protocol recognized, an entry will
only be created in that table if this value is supportedOn(3)
for both protocols. |
| Syntaxe | Enumeration (1-notSupported, 2-supportedOff, 3-supportedOn) |
| Module | RMON2-MIB (Force10-9.14.2.1) |
| Nom | protocolDirHostConfig |
| Acces | readwrite |
| Status | current |
| Description | This object describes and configures the probe's support for
the network-layer and application-layer host tables for this
protocol. When the probe creates entries in this table for
all protocols that it understands, it will set the entry to
notSupported(1) if it doesn't have the capability to track the
nlHostTable for this protocol or if the alHostTable is
implemented but doesn't have the capability to track this
protocol. Note that if the alHostTable is implemented, the
probe may only support a protocol if it is supported in both
the nlHostTable and the alHostTable.
If the associated protocolDirType object has the
addressRecognitionCapable bit set, then this is a network-
layer protocol for which the probe recognizes addresses, and
thus the probe will populate the nlHostTable and alHostTable
with addresses it discovers for this protocol.
If the value of this object is notSupported(1), the probe
will not track the nlHostTable or alHostTable for this
protocol and shall not allow this object to be changed to any
other value. If the value of this object is supportedOn(3),
the probe supports tracking of the nlHostTable and alHostTable
for this protocol and is configured to track both tables
for this protocol for all control entries and all interfaces.
If the value of this object is supportedOff(2), the probe
supports tracking of the nlHostTable and alHostTable for this
protocol but is configured to not track these tables
for any control entries or interfaces.
Whenever this value changes from supportedOn(3) to
supportedOff(2), the probe shall delete all related entries in
the nlHostTable and alHostTable.
Note that since each alHostEntry references 2 protocol
directory entries, one for the network address and one for the
type of the highest protocol recognized, an entry will
only be created in that table if this value is supportedOn(3)
for both protocols. |
| Syntaxe | Enumeration (1-notSupported, 2-supportedOff, 3-supportedOn) |
| Module | RMON2-MIB (FS) |
| Nom | protocolDirHostConfig |
| Acces | readwrite |
| Status | current |
| Description | This object describes and configures the probe's support for
the network layer and application layer host tables for this
protocol. When the probe creates entries in this table for
all protocols that it understands, it will set the entry to
notSupported(1) if it doesn't have the capability to track the
nlHostTable for this protocol or if the alHostTable is
implemented but doesn't have the capability to track this
protocol. Note that if the alHostTable is implemented, the
probe may only support a protocol if it is supported in both
the nlHostTable and the alHostTable.
If the associated protocolDirType object has the
addressRecognitionCapable bit set, then this is a network
layer protocol for which the probe recognizes addresses, and
thus the probe will populate the nlHostTable and alHostTable
with addresses it discovers for this protocol.
If the value of this object is notSupported(1), the probe
will not track the nlHostTable or alHostTable for this
protocol and shall not allow this object to be changed to any
other value. If the value of this object is supportedOn(3),
the probe supports tracking of the nlHostTable and alHostTable
for this protocol and is configured to track both tables
for this protocol for all control entries and all interfaces.
If the value of this object is supportedOff(2), the probe
supports tracking of the nlHostTable and alHostTable for this
protocol but is configured to not track these tables
for any control entries or interfaces.
Whenever this value changes from supportedOn(3) to
supportedOff(2), the probe shall delete all related entries in
the nlHostTable and alHostTable.
Note that since each alHostEntry references 2 protocol
directory entries, one for the network address and one for the
type of the highest protocol recognized, that an entry will
only be created in that table if this value is supportedOn(3)
for both protocols. |
| Syntaxe | Enumeration (1-notSupported, 2-supportedOff, 3-supportedOn) |